Refrigerant-134a enters an adiabatic compressor as saturated vapor at 100 kPa at a rate of 0.7 m3 /min and exits at 1-MPa pressure. If the isentropic efficiency of the compressor is 87 percent, determine
a) The temperature of the refrigerant at the exit of the compressor
b)The power input, in kW.
c) Show the process on a T-s diagram with respect to saturation lines.
Answers
The temperature of the refrigerant at the exit of the compressor is 57.6℃, the power input for the compressor is 105.78 kW, the process is shown on a T-s diagram with respect to saturation lines.
Refrigerant-134a enters an adiabatic compressor as saturated vapor at 100 kPa at a rate of 0.7 m³/min and exits at 1-MPa pressure.Isentropic efficiency of the compressor is 87 percent.
From the table of Refrigerant-134a, we can get the enthalpy of the refrigerant at state 1 & 2. The formula for the isentropic work of compressor is wS = h1 - h2sThe formula for the actual work of the compressor is w = h1 - h2.
a) The temperature of the refrigerant at the exit of the compressor: The temperature at state 1 is 37.9℃.
The refrigerant enters the compressor as a saturated vapor, and hence the temperature of the refrigerant at state 1 is 37.9℃. The refrigerant exits at a pressure of 1 MPa.The temperature of the refrigerant at the exit of the compressor is 57.6℃.
The temperature of the refrigerant at the exit of the compressor is 57.6℃.
b) The power input, in kW: The work done by the compressor is:w = h1 - h2, where h1 = 266.63 kJ/kg and h2 = 417.75 kJ/kg.w = 266.63 - 417.75 = -151.12 kJ/kg.
Since the rate of flow of refrigerant is 0.7 m³/min, the power input is:P = w × m = -151.12 × 0.7 = -105.78 kW. The compressor does not generate any power but requires an input power of 105.78 kW.
Therefore, the power input is 105.78 kW.
c) Show the process on a T-s diagram with respect to saturation lines.The isentropic process between states 1 and 2s is shown on a T-s diagram.The actual process between states 1 and 2 is shown on a T-s diagram below:
The above T-s diagram shows the refrigeration cycle. The solid line represents the refrigeration cycle. At state 1, the refrigerant enters the compressor as a saturated vapor and leaves the compressor at state 2 as a superheated vapor.
Learn more about temperature : brainly.com/question/27944554
#SPJ11
Related Questions
Participating in extracurricular activities in high school helps:
Answers
Answer:
Develop social skills
Explanation:
Answer:
strengthen your college applications
Explanation:
Need help with Part 1 – Additional Operations I MATLAB question
Answers
gove it to me. I'll do my best
Can anyone help me answer this question?
Consider an experimental design with two parameters of interest identified. The first parameter h has a range of 0 to 10 with increments of 2, and the second parameter has a range of 5 to 30 with increments of 5. If each experiment is repeated 4 times, determine the total number of measurements required.
Answers
In the two independent samples application with a continuous outcome, the parameter of interest in the test of hypothesis is the difference in population means, μ1-μ2.
What is hypothesis?A hypothesis (plural: hypotheses), in a scientific context, is a testable statement about the relationship between two or more variables or a proposed explanation for some observed phenomenon. In a scientific experiment or study, the hypothesis is a brief summation of the researcher's prediction of the study's findings, which may be supported or not by the outcome. Hypothesis testing is the core of the scientific method.The researcher's prediction is usually referred to as the alternative hypothesis, and any other outcome as the null hypothesis -- basically, the opposite outcome to what is predicted. (However, the terms are reversed if the researchers are predicting no difference or change, hypothesizing, for example, that the incidence of one variable will not increase or decrease in tandem with the other.)To learn more about hypothesis refer to:
https://brainly.com/question/11555274
#SPJ1
Can someone help me plz!!! It’s 23 points
Answers
Answer:
0.00695 A
Explanation:
µ represents \(10^{-6}\). Multiply this by 6,950.
_____is a slow wireless technology used to connect devices within a radius of about 30 feet
Answers
Answer:
Bluetooth is a slow wireless technology used to connect devices within a radius of about 30 feet. While Bluetooth technology is amazing, there are lots of bugs involved with Bluetooth devices, and there is still lots to be discovered in this area of tech.
Two friends are playing golf. The first friend hits a golf ball on level ground with an initial speed of 47.0 ms at an angle of 35.0∘ above the horizontal.
(a) Assuming that the ball lands at the same height from which it was hit, how far away from the golfer does it land? Ignore air resistance.
(b) The second friend hits another golf ball with the same initial speed as the first, but the initial velocity of the ball makes an angle with horizontal that is greater than 45 degrees. The second ball, however, travels the same horizontal distance as what you found in part (a), and it too lands at the same level from which it was hit. What was the angle in degrees above horizontal of the initial velocity of this second golf ball? Ignore air resistance.
Answers
Answer:
A) 211.81 m
B) 65°
Explanation:
We are told that the first friend hits a golf ball on level ground with an initial speed of 47 m/s at an angle of 35° above the horizontal.
Thus;
speed; u = 47 m/s
Projection angle; θ = 35°
A) We want to find how far away from the golfer the ball lands. This is simply the range. Range in projectile motion is given by the formula;
R = (u²•sin 2θ)/g
Plugging in the relevant values, we have;
R = (47² × sin(2 × 35))/9.8
R = 211.81 m
B) We are told that the second ball, travels the same horizontal distance as what is found in part (a).
Thus, R remains 211.81 m
Thus, the angle above horizontal of the initial velocity of this second golf ball will be;
90° - projection angle(θ) = 90 - 35 = 65°
superposition theorem
Answers
Answer:
mark me brainliest
Explanation:
Superposition theorem is one of those strokes of genius that takes a complex subject and simplifies it in a way that makes perfect sense. A theorem like Millman’s certainly works well, but it is not quite obvious why it works so well. Superposition, on the other hand, is obvious.
A group of scientists studied the environmental impact of internal combustion engines burning hydrocarbon fuels. The scientist equipped four vehicles with devices to capture and measure particulate emissions. One vehicle burned diesel fuel, one burned ordinary gasoline, one burned a gasoline/ethanol mixture and one burned natural gas. The four vehicles have equal masses and carried identical cargo. The scientists drove each vehicle 400 km, recording the volume of fuel burns in the quantity of particulate emissions generated. What is the independent variable in this experiment?
Answers
Answer: Combustion of Hydrocarbons
Explanation:
The Independent variable in an experiment is the one whose effect on the dependent variable is being measured. The independent variable therefore is controlled to see the effect it will have in the experiment.
In this experiment, the scientists combusted different types of hydrocarbons (diesel, gasoline, natural gas and a gasoline/ethanol mixture) as they aimed to find out the effect that this burning would have on the environment thereby making the combustion of hydrocarbons the independent variable.
Answer:
A. Type of Fuel
Explanation: The quantity of particulate Matter (PM) primarily depends upon the type of fuel used. Fine carbonaceous particles are mainly responsible for PM emissions. Diesel fueled vehicle engines are a major source of particulate emissions.
A technician wants to implement a dual factor authentication system that will enable the organization to authorize access to sensitive systems on a need-to-know basis. What should be implemented during the authorization stage?
Answers
Answer: Biometrics
Explanation:
Dual factor authentication refers to an electronic authentication method whereby a user will only be granted an access to an application or a website after the user has successfully been able to present two pieces of evidence which then grants access to the application or website.
Since the technician wants to implement a dual factor authentication system, the biometrics should be implemented during the authorization stage.
Biometrics refers to the body measurements and the calculations that are related to the characteristics of humans. Biometric authentication is used as a form of identification.
The inverted U-tube is used to measure the pressure difference between two points A and B in an inclined pipeline through which water flows. The differenceof level h=0.4m ; X=0.2; and Y=0.3m. Calculate the pressure difference between point B and A if the top of the manometer is filled with:
i) Air
ii) paraffin of relative density of 0.75
Answers
Answer:
i) 0.610 m or 610 mm
ii) 0.4 m or 400 mm
Explanation:
The pressure difference between the pipes is
a) Air
Pa + πha +Ha = Pb + πhb +Hb
Pa - Pb = π(hb-ha) + Hb-Ha
Relative density of air = 1.2754 kg /m3
Pa - Pb = 1.2754 * 0.4 + (0.3-0.2) = 0.610 m or 610 mm
b) paraffin of relative density of 0.75
Pa - Pb = π(hb-ha) + Hb-Ha
Pa - Pb = 0.75 * 0.4 + (0.3-0.2) = 0.4 m or 400 mm
The proposed grading at a project site will consist of 25,100 m3 of cut and 23,300 m3 of fill and will be a balanced earthwork job. The cut area has an average moisture content of 8.3%. The fill will be compacted to an average relative compaction of 93% based on a maximum dry unit weight of 18.3 kN/m3 and an optimum moisture content of 12.9% obtained from the modified Proctor test. Compute the volume of water in kiloliters that will be required to bring these soils to the optimum moisture content.
Answers
M = ((Ww / Ws) x 100)%
where M is the moisture content, Ww is the weight of water, and Ws is the weight of solids.
First, let's find the weight of solids for the cut area:
Ws = V x γ
where V is the volume and γ is the unit weight.
Ws = 25,100 m3 x 1.8 t/m3 x 1000 kg/t
Ws = 45,180,000 kg
Next, let's find the weight of solids for the fill area:
Ws = V x γ
where V is the volume and γ is the unit weight.
Ws = 23,300 m3 x 18.3 kN/m3 x 1000 N/kN
Ws = 425,190,000 N
Now, let's find the weight of water required for the cut area:
M = ((Ww / Ws) x 100)%
0.129 = ((Ww / 45,180,000) x 100)%
Ww = 58,402 kg
Finally, let's find the weight of water required for the fill area:
M = ((Ww / Ws) x 100)%
0.129 = ((Ww / 425,190,000) x 100)%
Ww = 548,991 kg
To find the total volume of water required, we need to convert the weight of water to volume using the density of water:
ρ = 1000 kg/m3
For the cut area:
Vw = Ww / ρ
Vw = 58,402 kg / 1000 kg/m3
Vw = 58.4 m3
For the fill area:
Vw = Ww / ρ
Vw = 548,991 kg / 1000 kg/m3
Vw = 548.991 m3
Therefore, the total volume of water required to bring the soils to the optimum moisture content is approximately 607.4 m3 or 607.4 kiloliters.
For the electrochemical cell:
Cd (s)/Cd2+ (ac)// Co2+ (ac)/Co (s).
Co2+ + 2 e- → Co E° = -0.28 V
Cd2+ + 2 e- → Cd E° = -0.403 V
Determine the equilibrium constant (Kc) at 25 °C for the reaction that occurs:
a. 1,4 x 102
b. 1,4 x 10-23
c. 9.4 x 1022
d. 7,0 x 10-5
e. 1,4 x 104
Answers
To determine the equilibrium constant (Kc) for the given electrochemical cell reaction at 25 °C, we can use the Nernst equation:
E = E° - (RT / nF) * ln(Kc)
Where:
E is the cell potential under non-standard conditions,
E° is the standard cell potential,
R is the gas constant (8.314 J/(mol·K)),
T is the temperature in Kelvin,
n is the number of electrons involved in the reaction, and
F is the Faraday constant (96,485 C/mol).
In this case, the cell reaction is:
Co2+ + 2 e- → Co (s)
Cd (s) → Cd2+ + 2 e-
To determine Kc, we need to write the balanced equation for the overall reaction, which can be obtained by combining the half-reactions: Co2+ + Cd (s) → Co (s) + Cd2+
The number of electrons involved in the reaction is 2. Given the standard cell potentials:
E°(Co2+/Co) = -0.28 V
E°(Cd2+/Cd) = -0.403 V
Substituting the values into the Nernst equation, we have: E = -0.28 - (8.314 * 298 / (2 * 96,485)) * ln(Kc)
Simplifying further: E = -0.28 - 0.01067 * ln(Kc)
At equilibrium, the cell potential (E) is zero since the reaction is in a state of dynamic equilibrium. Thus, we have:
0 = -0.28 - 0.01067 * ln(Kc)
Rearranging the equation and solving for ln(Kc): ln(Kc) = -0.28 / 0.01067
Using a calculator, we find that ln(Kc) ≈ -26.247. Now, we can solve for Kc:
Kc = e^(ln(Kc))
Kc = e^(-26.247)
Kc ≈ 1.41 × 10^(-12)
Comparing the calculated value with the given options, we see that the closest option is: b. 1.4 x 10^(-23)
Therefore, the equilibrium constant (Kc) at 25 °C for the reaction is approximately 1.4 × 10^(-23).
To know more about Nernst equation visit:
https://brainly.com/question/32004806
#SPJ11
A wheel tractor is operating in it is fourth gear range with full rated revolution per minute. Tractors speed is 7.00 miles per hour. Ambien air temperature is 60 Fahrenheit, and operating attitude is sea level. This tractor is towing a fill material loaded pneumatic trailer while climbing with 5 % slop. Rolling resistance is 55lb/ton. Tractor is single axle and it is operating weight is 74,946 lb. The loaded trailer weighs 55,000 lb. The weight distribution is for the combined tractor- trailer unit is 53% to the drive axle and 47% to the rear axle.
The manufacturer, for the environmental conditions as given above, rates the tractive effort of the new tractor at 330 rimpull HP. What percentage of this manufacturers rated rimpul HP actually develop?
Answers
calculate the value of the height h required to provide the desired flow rate of detergent into the wasshing machine when the vavle is fully opened
Answers
Answer:
Hello your question is incomplete attached below is the complete question
answer: 4.54 m
Explanation:
To calculate the value of the height ( h ) required we will use Bernoulli's equation
attached below is a detailed solution
The width of a frictional material on a multiple disc clutch is (r2 -r1) and is equal to half of the maximum radius (R); The maximum diameter of the coupling is not to exceed 162 mm. What is the inside diameter in mm?
Answers
Since the width of a frictional material on a multiple disc clutch is (r₂ - r₁) the inside diameter of the multiple disc clutch is 81 mm
How to calculate the inside diameter multiple disc clutch?Let
w = width of frictional material r = inside radius multiple disc clutch and r = outside radius multiple disc clutchGiven that the width of a frictional material on a multiple disc clutch is (r₂ - r₁) and is equal to half of the maximum radius (R), we have that
w = r₂ - r₁ (1)and
w = R/2 (2)
Since R = r₂
w = r₂/2 (3)
Equating equations (1) and (3), we have
r₂ - r₁ = r₂/2
r₁ = r₂ - r₂/2
r₁ = r₂/2
Since the maximum diameter d₂ of the coupling is not to exceed 162 mm, we have that
r₂ = d₂/2
So, r₁ = r₂/2
r₁ = d₂/4
r₁ = 162 mm/4
r₁ = 40.5 mm
Now the inside diameter d₁ = 2r₁
So, d₁ = 2 × 40.5 mm
= 81 mm
So, the inside diameter of the multiple disc clutch is 81 mm
Learn more about inside diameter here:
https://brainly.com/question/27231407
#SPJ1
tyuuyiopopiouyttrrtrffrlkl,k;;';'l.l
Answers
Answer:
Explanation:
do you have any other questions besides "tyuuyiopopiouyttrrtrffrlkl,k;;';'l.l"
#include
void main()
(
int x = 1, z = 3;
}
int y = x << 3;
printf("%d\n",y);
-2147483648
-1
Run time error
8
Answers
Answer:
Americans is great
It is desirable to model a battery by its Thevenin equivalent. To do this, two precision resistors are used. In particular, a 25 Ohm resistor gives a 20 V drop and a 15 Ohm resistor gives a 15 V drop. The Thevenin's equivalent resistance is most nearly
1. 100 ohms
2. 75 Ohms
3. 25 Ohms
4. 15 Ohms
5. 40 Ohms
Answers
Answer:
3. 25 ohms
Explanation:
Already we are aware that
Vth = IRth + VL
RL = 25 ohms
VL = 20v
I = vL/RL
I = (20/25)A
Vth = (20/25)Rth + 20
25Vth = 20Rth + 20x25
= 25Vth - 20Rth + 500 --- (a)
RL = 15 ohms VL = 15v
I = 15/15 = 1A
Vth = 1 x Rth + 15
Vth - Rth = 15 --- (b)
When we solve equations a and b simultaneously,
Vth = 40V, Rth = 25 ohms
Therefore the answer is 25ohms.
A(n) _____ is a diagram used during both the analysis and design phases of a systems development life cycle (SDLC) to document the processes of the current system or to provide a model of a proposed new system.
Answers
A Data Flow Diagram (DFD) is a diagram used during both the analysis and design phases of a Systems Development Life Cycle (SDLC) to document the processes of the current system or to provide a model of a proposed new system.
DFDs visually represent the flow of data within a system, illustrating how inputs are transformed into outputs through various processes and data storage components.
In the analysis phase, DFDs help to identify inefficiencies and areas for improvement in the existing system, facilitating a thorough understanding of the current processes. This is critical for identifying potential enhancements and creating a comprehensive specification for the new system.
During the design phase, DFDs serve as a blueprint for the development of the new system. They provide clear, concise visualizations of the system's architecture, ensuring that all stakeholders understand the proposed processes and their interactions. This helps streamline communication and minimize misunderstandings during the development process.
DFDs consist of several components, including external entities, processes, data stores, and data flows. External entities represent sources or destinations of data outside the system, while processes depict the transformations and operations performed on the data. Data stores are used to represent the storage of data within the system, and data flows illustrate the movement of data between components.
In summary, a Data Flow Diagram is a valuable tool used during the SDLC to effectively document, analyze, and design systems, ensuring a comprehensive understanding of both current and proposed processes.
Learn more about Data Flow Diagram here:-
https://brainly.com/question/29418749
#SPJ11
In Problem 15.1, assume that the fine aggregate contains 7% free moisture by weight, and the coarse aggregate contains 3% free moisture by weight. Determine the required weights of cement, fine aggregate, coarse aggregate, and volume of added water for an 8-cy batch.
Answers
To accurately ascertain the necessitated weights of cement, fine aggregate, coarse aggregates, and the volume of added water for a 8-cy batch of concrete, one must comprehend both the mix design proportions and the bulk densities of each substance.
How to explain rye informationI can provide general instructions on tackling this challenge. In order to discover the total dry aggregate weight mandatory for an 8-cy batch, you will have to multiply the amount of concrete with the gathered bulk density of all materials combined.
Calculate the individual weights of both fine aggregate and coarse aggregate taking into consideration the estimated moisture content in each. Figure out the mandatory amount of cement based on the ratios presented within the mix design.
Also, calculate the needed volume of water by accounting for the moisture content among the components and utilizing information from the designated water-cement ratio mentioned in the proposed combo-design.
Learn more about moisture on
https://brainly.com/question/10398867
#SPJ1
Which of these is true for prototypes?
a. Horizontal Prototypes does some processing apart from the required for presenting the productâs user interface
b. Vertical Prototype realizes part or all of a productâs user interface
c. All of the mentioned
d. None of the mentioned
Answers
Answer:c
Explanation:
Briefly explain thermal expansion using the potential energy–versus–interatomic spacing curve.
Answers
As the temperature of the material increases, the potential energy of the molecules increases. Thermal expansion occurs due to changes in temperature, and interatomic distances increase as potential energy increases.
What are the uses of Thermal Expansion?Thermal expansion is used in a variety of applications such as rail buckling, engine coolant, mercury thermometers, joint expansion, and others.
It is to be noted that an application of the concept of liquid expansion in everyday life concerns liquid thermometers. As the heat rises, the mercury or alcohol in the thermometer tube moves in only one direction. As the heat decreases, the liquid moves back smoothly.
Learn more about Thermal Expansion:
https://brainly.com/question/1166774
#SPJ1
Determine the resistance of 3km of copper having a diameter of 0,65mm if the resistivity of copper is 1,7x10^8
Answers
Answer:
Resistance of copper = 1.54 * 10^18 Ohms
Explanation:
Given the following data;
Length of copper, L = 3 kilometers to meters = 3 * 1000 = 3000 m
Resistivity, P = 1.7 * 10^8 Ωm
Diameter = 0.65 millimeters to meters = 0.65/1000 = 0.00065 m
\( Radius, r = \frac {diameter}{2} \)
\( Radius = \frac {0.00065}{2} \)
Radius = 0.000325 m
To find the resistance;
Mathematically, resistance is given by the formula;
\( Resistance = P \frac {L}{A} \)
Where;
P is the resistivity of the material. L is the length of the material.A is the cross-sectional area of the material.First of all, we would find the cross-sectional area of copper.
Area of circle = πr²
Substituting into the equation, we have;
Area = 3.142 * (0.000325)²
Area = 3.142 * 1.05625 × 10^-7
Area = 3.32 × 10^-7 m²
Now, to find the resistance of copper;
\( Resistance = 1.7 * 10^{8} \frac {3000}{3.32 * 10^{-7}} \)
\( Resistance = 1.7 * 10^{8} * 903614.46 \)
Resistance = 1.54 * 10^18 Ohms
2-design a set of simple test programs to determine the type compatibility rules of a c compiler to which you have access. Write a report of your findings
Answers
When designing a set of simple test programs to determine the type compatibility rules of a C compiler to which you have access, it is important to consider the different data types that are used in C programming. An example of a set of test programs that can be used to determine the type compatibility rules of a C compiler:
Integer Test the compatibility of the C compiler with integer data types. It declares two variables of type int, initializes them with values, and then adds them together. The result is printed to the screen. If the program compiles and runs without any errors, then the C compiler is compatible with integer data types.
Floating-Point Test the compatibility of the C compiler with floating-point data types. It declares two variables of type float, initializes them with values, and then adds them together. The result is printed to the screen. If the program compiles and runs without any errors, then the C compiler is compatible with floating-point data types.
By running the set of simple test programs described above, you can determine the type compatibility rules of a C compiler to which you have access. If any of the programs do not compile or run without errors, then you can determine which data types are not compatible with the C compiler and adjust your code accordingly.
To know more about compiler visit:-
https://brainly.com/question/28232020
#SPJ11
Select the correct answer.
Which statement is true regarding the use of Kirchhoff’s laws?
A.
The voltage change across a resistor is negative when you traverse in the opposite direction of the current.
B.
Some current is lost at the junction due to resistance across all resistors in the circuit.
C.
Every loop should contain junctions from where current branches out in different directions.
D.
The voltage change across a resistor is zero when you traverse in the opposite direction of the current.
E.
The sum of currents flowing into a junction is more than the sum flowing out of it.
Answers
Answer:
A.
Explanation:
The voltage change across a resistor is negative when you traverse in the opposite direction of the current.
What does efficiency measure?
Answers
Answer:
Efficiency is defined as any performance that uses the fewest number of inputs to produce the greatest number of outputs. Simply put, you're efficient if you get more out of less.
Explanation:
Please help me solve the assignment
Answers
In this instance, interleaving refers to the system performing a single physical memory access while utilising more than one memory bank.
What is memory bank?For storing and retrieving frequently used data, a memory bank is a logical storage area within computer memory. For quick access to and retrieval of programs and common data, it may be a component of regular RAM or the cache memory. Bank switching is a mechanism that sets up the memory that the CPU can access at any given time. Since the MOS 6510 CPU can only access 216 = 65536 memory addresses ($0000-$FFFF), banks of memory can be switched (which makes them visible or invisible to the CPU) to increase total capacity. The data memory address bus is 12 bits, and it can address up to 4 MB of memory. Each bank in the RAM has 256 bytes and there are 16 of them overall.To learn more memory bank refer to:
https://brainly.com/question/13911669
#SPJ1
WHAT PARTS OF THE BRAKE LAMP SYSTEM CAN FAIL? DESCRIBE HOW?
Help me ASAP please
Answers
Answer:
Explanation:
Brake systems are most likely to fail at the ends. One of the most common problems is a trailer lighting splitter is left on. With time and usage, the fuse can blow interrupting the signal path from the switch to the bulb.
Answered by the ONE & ONLY #QUEEN aka #DRIPPQUEENMO
HOPE THIS HELPED!!!
determine the maximum magnitude p of the loads the beam can support if the average shear stress in each pin is not to exceed 80 mpa. all pins are in double shear, and each has a diameter of 18 mm.
Answers
The maximum magnitude of the load the beam can support is 547.16 N.
The maximum magnitude of the load the beam can support can be calculated using the formula:
p = 2 * τ * π * d^2 / (4 * n)
where:
τ is the maximum allowable shear stress (80 MPa)
d is the diameter of the pins (18 mm)
n is the number of pins in double shear
Converting the diameter to meters, we have:
d = 18 * 10^-3 m
Let's assume n=2 pins in double shear. Then,
p = 2 * 80 * 10^6 * π * (18 * 10^-3)^2 / (4 * 2)
p = 547.16 N
So, the maximum magnitude of the load the beam can support is 547.16 N.
learn more about the maximum load capacity of a beam here:https://brainly.com/question/16980313
#SPJ4
Waterbutt filtration system for pond. Water pressure principles, help needed?
I have water butt 1 and 2 working perfectly but as soon as I add another to the system water butt 1 and 2 start rising and overflowing.
Is there something I'm missing or doing wrong here? How does water leveling work?
Thanks all.
Answers
Water pressure principles is known to state that the amount of Fluid pressure is said to be perpendicular to the surface on which it it exert or works on.
Note that principle is shown by a vessel that is said to be having flat sides and has water. The pressure exerted by the weight of the water is therefore known to be perpendicular to the walls of the storage.
What is a Waterbutt used for?A water butt is known to be a container that is made and also used to store a lot of rainwater.
Note that Water pressure principles is known to state that the amount of Fluid pressure is said to be perpendicular to the surface on which it it exert or works on.
Learn more about Water pressure principles from
https://brainly.com/question/14813457
#SPJ1