an ideal transformer has a primary input of 120 volts (measured with a digital volt meter) at 60 hz and 600 turns in the primary winding. the secondary winding has 3000 turns and is connected to a load of 6000 ohms. determine (a) the turns ratio (b) the secondary voltage (c) the secondary power (d) the primary power (e) the primary current (f) the secondary frequency.
Answers
The secondary frequency is the same as the primary frequency, which is 60 Hz.
(a) The turns ratio of the transformer is given by:
turns ratio = N_secondary / N_primary
= 3000 / 600
= 5
(b) The secondary voltage is given by:
V_secondary = V_primary / turns ratio
= 120 / 5
= 24 volts
(c) The secondary power is given by:
P_secondary = (V_secondary)² / R_load
= (24)² / 6000
= 0.096 W
(d) The primary power is equal to the secondary power, neglecting losses, so:
P_primary = P_secondary
= 0.096 W
(e) The primary current is given by:
I_primary = P_primary / V_primary
= 0.096 / 120
= 0.0008 A
To know more about transformer,
https://brainly.com/question/15200241
#SPJ11
Related Questions
The DOT places more restrictions on operators of heavy trucks than on lighter trucks. Why do you think this is?
Only the states can regulate drivers of light trucks.
The drivers of heavy trucks go on long hauls, and therefore are most likely to engage in smuggling and related activities that might pose a national security risk.
The DOT does not actually place more restrictions on operators of heavy trucks.
The DOT is tasked with protecting the safety of people on the roadways, and long hauls pose more such risks.
Answers
The DOT places more restrictions on operators of heavy trucks than on lighter trucks. The reason for this is that "The DOT is tasked with protecting the safety of people on the roadways, and long hauls pose more such risks."
What is the DOT?The United States Department of Transportation (or DOT) is a federal cabinet department of the United States government involved with transportation. It was founded in 1966 and went into operation on April 1, 1967. The United States Secretary of Transportation is in charge of it.
Its goal statement is: "To serve the United States by assuring a rapid, safe, efficient, open, and convenient transportation system that satisfies our essential national interests and improves the quality of life of the American people today and in the future."
Learn more about DOT:
https://brainly.com/question/14329984
#SPJ1
The present worth of income from an investment that follows an arithmetic gradient is projected to be $475,000. The income in year one is expected to be $25,000. What is the gradient each year through year 6 at an interest rate of 10% per year?
I found this on another site:
475,000 = 25,000(P/A,10%,6) + G(P/G,10%,6)
475,000 = 25,000(4.3553) + G(9.6842)
9.6842G = 366,117.50
G = $37,805.65
Answers
Answer:
G = $37,805.65
Explanation:
I found this on another site:
475,000 = 25,000(P/A,10%,6) + G(P/G,10%,6)
475,000 = 25,000(4.3553) + G(9.6842)
9.6842G = 366,117.50
G = $37,805.65
The gradient each year through at an interest rate of 10% per year is $37,805.65.
What is investment?Investment refers to the money spend on the acquiring the assets and also to build up the capital for the businessmen and wealth for the individual. It involves saving of the money.
Investment is the collection of the money from other primary source of the income. It also includes profit gains from the investment over a specific period of time.
According to the question, projected arithmetic gradient is $475,000 and estimated income for one year is $25,000.
Thus, the gradient for each year is calculated as follows:-
475,000 = 25,000(P/A,10%,6) + G(P/G,10%,6)
475,000 = 25,000(4.3553) + G(9.6842)
9.6842G = 366,117.50
Gradient = $37,805.65
Therefore, it can be concluded that gradient each year through at an interest rate of 10% per year is $37,805.65.
Learn more about investment here:
https://brainly.com/question/14019511
#SPJ2
Find the bases for the eigenspaces ofa. (show your work or write an explanation foryour answer.
Answers
The eigenvalues of matrix A are λ = 5 and λ = 2, and the corresponding eigenvectors are [1, -2] and [1, -1] respectively.
We have,
To determine the eigenvalues and corresponding eigenvectors of matrix A, we need to solve the characteristic equation.
The characteristic equation is given by det(A - λI) = 0, where A is the matrix, λ is the eigenvalue, and I is the identity matrix.
Let's proceed with the calculation:
A = [[3, -1], [2, 4]]
The identity matrix I for a 2x2 matrix is:
I = [[1, 0], [0, 1]]
Now, we can write the characteristic equation:
det(A - λI) = 0
Substituting the values, we have:
det([[3, -1], [2, 4]] - λ[[1, 0], [0, 1]]) = 0
Simplifying, we get:
det([[3 - λ, -1], [2, 4 - λ]]) = 0
Expanding the determinant, we have:
(3 - λ)(4 - λ) - (-1)(2) = 0
Simplifying further:
(λ - 3)(λ - 4) + 2 = 0
Expanding and rearranging, we get:
λ² - 7λ + 10 = 0
This is a quadratic equation that can be factored:
(λ - 5)(λ - 2) = 0
Setting each factor equal to zero, we find two eigenvalues:
λ - 5 = 0, which gives λ = 5
λ - 2 = 0, which gives λ = 2
Now, let's find the eigenvectors corresponding to each eigenvalue.
For λ = 5:
We need to solve the equation (A - 5I)v = 0, where v is the eigenvector.
(A - 5I) = [[3, -1], [2, 4]] - 5[[1, 0], [0, 1]]
= [[3, -1], [2, 4]] - [[5, 0], [0, 5]]
= [[-2, -1], [2, -1]]
To find the eigenvector, we solve the equation:
[[-2, -1], [2, -1]][x, y] = [0, 0]
Simplifying further, we get two equations:
-2x - y = 0
2x - y = 0
Solving these equations, we find that y = -2x.
Choosing a value for x, let's say x = 1, we can find y:
y = -2(1) = -2
So, one eigenvector corresponding to λ = 5 is [1, -2].
For λ = 2:
We need to solve the equation (A - 2I)v = 0, where v is the eigenvector.
(A - 2I) = [[3, -1], [2, 4]] - 2[[1, 0], [0, 1]]
= [[3, -1], [2, 4]] - [[2, 0], [0, 2]]
= [[1, -1], [2, 2]]
To find the eigenvector, we solve the equation:
[[1, -1], [2, 2]][x, y] = [0, 0]
Simplifying further, we get two equations:
x - y = 0
2x + 2y = 0
Simplifying these equations, we find that y = -x.
Choosing a value for x, let's say x = 1, we can find y:
y = -1
So, one eigenvector corresponding to λ = 2 is [1, -1].
Therefore,
The eigenvalues of matrix A are λ = 5 and λ = 2, and the corresponding eigenvectors are [1, -2] and [1, -1] respectively.
Learn more about matrix here:
https://brainly.com/question/28180105
#SPJ4
The complete question:
Consider the matrix A = [[3, -1], [2, 4]].
Determine the eigenvalues and corresponding bases for the eigenspaces of matrix A.
A parallel circuit has a resistance of 280 and an inductive reactance of 360 02. What's this circuit's impedance?
Answers
Answer:
540 W
Explanation:
In Value Engineering (VE) what does the acronym TIPS stand for
and what is its primary focus?
Answers
TIPS is an acronym in Value Engineering (VE) that stands for Technique, Information, Product, and Schedule.The primary focus of the TIPS approach is to improve the performance of the product or service by using creative and innovative methods to achieve the same results at a lower cost.
It is used to achieve a significant increase in the value of a product or service while lowering its cost. The primary focus of the TIPS approach is to improve the performance of the product or service by using creative and innovacronymative methods to achieve the same results at a lower cost.
Value Engineering (VE) is a systematic approach that is used to improve the value of a product or service. It is a method that is used to optimize the function and cost of a product or service by analyzing its various components and identifying ways to improve its performance while reducing its cost. The goal of value engineering is to achieve the highest possible value for a product or service while minimizing its cost.
TIPS is an acronym that stands for Technique, Information, Product, and Schedule. It is an approach that is used in Value Engineering to improve the performance of a product or service while lowering its cost.
The primary focus of the TIPS approach is to use innovative and creative methods to achieve the same results at a lower cost. By using this approach, a product or service can be optimized to achieve maximum value while minimizing its cost.
TIPS is used in Value Engineering to:Identify techniques that can be used to improve the performance of a product or serviceIdentify information that is needed to improve the performance of a product or serviceIdentify ways to optimize the product or service to improve its value while reducing its costIdentify ways to schedule the work to achieve the best possible results in the shortest possible time.
Learn more about acronym here,
https://brainly.com/question/20664471
#SPJ11
Draw the megnetization current or circut of generatpr characterstistics and explian the shape
Answers
what causes your car to eventually slow down and stop when you take your foot off the gas pedal
Answers
Some_____
include peanut butter, bacon, and chocolate.
Snap traps baits
Glue boards
Catchalls
IGRs
Bait stations
Answers
Answer:
it’s IGS
Explanation:
because i read
Answer:
snap trap baits
Explanation: its kind of obvi, but i took the test and got it right.
An air-conditioning system operates at a total pressure of 1 atm and consists of a heating section and a humidifier that supplies wet steam (saturated water vapor) at 1008C. Air enters the heating section at 108C and 70 percent relative humidity at a rate of 35 m3/min, and it leaves the humidifying section at 208C and 60 percent relative humidity. Determine (a) the temperature and relative humidity of air when it leaves the heating section, (b) the rate of heat transfer in the heating section, and (c) the rate at which water is added to the air in the humidifying section.
Answers
Correct question is;
An air-conditioning system operates at a total pressure of 1 atm and consists of a heating section and a humidifier that supplies wet steam (saturated water vapor) at 100°C. Air enters the heating section at 10°C and 70 percent relative humidity at a rate of 35 m3/min, and it leaves the humidifying section at 20°C and 60 percent relative humidity. Determine (a) the temperature and relative humidity of air when it leaves the heating section, (b) the rate of heat transfer in the heating section, and (c) the rate at which water is added to the air in the humidifying section.
Answer:
A) Temperature at state 2: T2 = 19.5°C and Relative Humidity at state 2: Φ2 = 37.8%
B) Q' = 420.01 KJ/min
C) m'w = 0.1472 Kg/min
Explanation:
This question depicts a steady state process and as such the mass flow rate of dry air will remain constant during the entire process.
A) Now, from the psychometric chart attached, at temperatures of T1 = 10°C & T3 = 20°C, Relative humidities; Φ2 = 70% & Φ2 = 60% and at pressure of 1 atm, we have;
Enthalpy at state 1;h1 = 23.5 Kj/kg dry air
Absolute humidity at state 1;ω1 = ω2 = 0.0053 kg of water per kg dry air
Enthalpy at state 3;h3 = 42.3 KJ/Kg dry air
Absolute humidity at state 3; ω3 = 0.0087 kg of water per Kg dry air
Specific volume at state 1;υ1 = 0.809 m³/kg
The formula for energy balance for the humidifying is given as;
h3 = h2 + hg(ω3 - ω2)
Where hg is the enthalpy of wet steam.
From second table attached, hg at 100°C is 2675.6 KJ/kg
Thus;
Making h2 the subject, we have;
h2 = h3 + hg(ω2 - ω3)
Plugging in the relevant values we have;
h2 = 42.3 + 2675.6(0.0053 - 0.0087)
h2 = 33.2 KJ/kg
Still using the psychrometric chart attached at ω2 = 0.0053 and h2 = 33.2 KJ/kg, we have;
Temperature at state 2: T2 = 19.5°C and Relative Humidity at state 2: Φ2 = 37.8%
B) to determine the rate of heat transfer, let's first find the mass flow rate first;
m' = V1'/υ1
Thus, m' = 35/0.809
m' = 43.3 kg/min
Thus, rate of heat transfer is given by;
Q' = m'(h2 - h1)
Plugging in the relevant values, gives;
Q' = 43.3(33.2 - 23.5)
Q' = 420.01 KJ/min
C) the rate at which water is added to the air in the humidifying section is given by;
m'w = m'( ω3 - ω2)
m'w = 43.3(0.0087 - 0.0053)
m'w = 0.1472 Kg/min
Is the flow of power reversible in a worm and wheel gear
Answers
The flow of power cannot be reversed since the slider could not move the worm gears. Since the input has one continuous tooth and the output has not teeth there is no gear ratio and no change in torque and speed.
Most technicians install rebuilt or new power steering pumps rather than overhauling the defective unit in the shop. True or False?
Answers
Answer:
Most technicians install rebuilt or new power steering pumps rather than overhauling the defective unit in the shop.
True
Explanation:
It has been established that most technicians, instead of overhauling the defective power steering pumps, prefer to install rebuilt or revamped pumps or even new pumps when they could have overhauled the unit themselves. Some are afraid that leakage could occur again. They are not confident enough to do the overhauling in-house or some claim that they do not have the time and other tools to carry out the overhauling. Acknowledgedly, overhauling a power steering pump is not a job for the novice. They require experienced and skilled hands to do the hard work.
An adult inhales approximately 12 times per minute, taking in about 500. mL of air per breath. Oxygen and carbon dioxide are exchanged in the lungs, but no nitrogen is exchanged. The exhaled mole fraction of nitrogen is 0.75 and is saturated with water vapor at body temperature 37°C. The ambient conditions are 25°C and 50% relative humidity. What volume of liquid water (mL) would need to be consumed to over a two-hour period to replace the water loss from breathing?
Answers
8.46 mL volume of liquid water (mL) would need to be consumed to over a two-hour period to replace the water loss from breathing.
What is Volume?
The space occupied within an object's borders in three dimensions is referred to as its volume. It is sometimes referred to as the object's capacity.
Given that;
Volume of air taken in each inhalation = 500 mL = 0.5 L
Relative moisture = 50
At 25 oC, vapor pressure of water = 23.8 mm Hg
Relative moisture = partial pressure of water vapor/ vapor pressure of liquid
Partial pressure of water vapor = Relative moisture * vapor pressure of liquid = 23.8 *0.5 = 11.4 mm Hg
intelligencers of gas exhaled is given as
n = PV/ RT
n = 1 *0.5/(0.0821 *( 37273.15)
n = 0.0196 intelligencers of gas/ 12minutes
For two hour period = 2 * 60 = 120 twinkles
intelligencers of air needed in 120 twinkles = 120 *0.0196/ 12 = 0.196 intelligencers of air
operative bit of nitrogen = 0.75
intelligencers of nitrogen = operative bit * total intelligencers = 0.75 *0.196 = 0.147 intelligencers
Partial pressure of water vapor/ partial pressure of nitrogen = intelligencers of water vapor/ intelligencers of nitrogen/(0.75 * 1) = intelligencers of water vapor/0.147
intelligencers of water vapor = 11.4 *0.147/0.75 = 2.2344 intelligencers of water = 2.2344 * 18 gm = 40.22 gm
viscosity of water = 1 g/ mL
Volume of water = 40.22/ 1 = 40.22 mL
When the person is in airplane:
Relative moisture = 10
Partial pressure of water vapor = 23.8 *0.1 = 2.38 mmHg /0.75 = intelligencers of water vapor/0.147
intelligencers of water vapor = 2.38 *0.147/0.75 = 0.47 intelligencers = 0.47 * 18 = 8.46 gm
Volume of water = 8.46/ 1 = 8.46 mL
Learn more about Volume click here:
https://brainly.com/question/20725746
#SPJ1
The entire population of a given community is examined, and all who are judged to be free from bowel cancer are questioned extensively about their diets. These people then are followed for several years to see whether their eating habits will predict their risk of developing bowel cancer. Which of the following study designs most appropriately characterizes this situation?
A. Cross-sectional study.
B. Case-control study.
C. Prospective cohort study.
D. Historical prospective cohort study.
E. Clinical trial.
F. Community trial.
Answers
Answer:
C) Prospective Cohort study
Explanation:
prospective cohort study can be regarded as longitudinal cohort study that comes up with periods of time when group of individuals that are different in terms of some factors that are undergoing some study, so that how theses factors influence rates of some particular outcomes can be known.
Suggest how the following requirements might be rewritten in a
quantitative way:
a. The library system shall be easy-to-use.
b. The library system shall provide reliable service to all classes of
user.
c. The library system shall provide a rapid response to all user
requests for book information.
Answers
Answer:
answer letter c
Explanation:
yun anserr hhehehe
Have you ever prototyped an idea? How did you do it?
Answers
Yes, I have prototyped an idea.
How to prototype an idea?
STEP-1 Create Your Ideas Now: Here are some initial steps you may take to speed up the idea-generation process. Conduct in-depth research Know the market value, potential rivals, manufacturing method, and overall cost of your goods.
STEP-2 Make a Simplified Version of Your Idea: Making a straightforward representation of your idea would be the next step after conducting considerable research and settling on an idea.
STEP-3 Make a Realistic Prototype: You actually start working on your prototype at this point.
STEP-4 Develop Your Prototype Until It Is Perfect: The hardest and longest phase of them all is this one.
Hence, the prototype of an idea is given.
To learn more about the Prototype from the given link
https://brainly.com/question/27896974
#SPJ9
*sapnap teaching you how to drive*
"Skeppy and Badboyhalo are crossing the street, what do you hit?"
"Skeppy, I would never hurt Bad."
"whA- THE BRAKES YOU HIT THE BREAKS!!"
*Dream wheezing from the back*
Answers
Answer:
yes dream
Explanation:
Answer:
Me: "i would just hit you, sapnap. In the freaking face" LOL
it's in the picture please asap
Answers
when deciding where to locate their assembly plants, car manufacturers want to locate in certain areas primarily for their closer access to...
Answers
When deciding where to locate their assembly plants, car manufacturers want to locate in certain areas primarily for their closer access to Supply chains and transportation networks.
What is supply chain?A supply chain is a sophisticated logistics system made up of facilities that turn raw materials into completed goods that are then transferred to end users or customers. Meanwhile, supply chain management is concerned with the most effective movement of commodities within the supply chain.
Purchasing, Manufacturing, Inventory Management, Demand Planning, Warehousing, Transportation, and Customer Service are the seven key functional areas of supply chain.
Learn more about assembly plants at:
https://brainly.com/question/26948522
#SPJ1
Explain the 11 sections that a typical bill of quantity is divided into
Answers
Answer:
The main sections included in the bill of quantities are Form of Tender, Information, Requirements, Pricing schedule, Provisional sums, and Day works.
Which indications are acceptable tolerances when checking both VOR receivers by use of the VOT?
Answers
It is important to note that these tolerances are established by the Federal Aviation Administration (FAA) and must be met in order for the VOR system to be considered operational and reliable. Any discrepancies or deviations from these tolerances should be addressed and corrected before the aircraft is flown.
When checking both VOR receivers by use of the VOT (VOR Operational Test), the acceptable tolerances are as follows:
1. Course deviation indicator (CDI) centering - The CDI should be centered within plus or minus 4 degrees of the 0-degree position.
2. Course indication - The course indication should be accurate to within plus or minus 6 degrees of the VOR radial selected.
3. Reverse sensing - When flying outbound from the VOR station, the CDI should show full scale deflection in the direction opposite to the selected course. When flying inbound, the CDI should show normal deflection toward the selected course.
4. Signal strength - The signal strength should be sufficient to provide a useable and reliable signal at all times during the flight.
It is important to note that these tolerances are established by the Federal Aviation Administration (FAA) and must be met in order for the VOR system to be considered operational and reliable. Any discrepancies or deviations from these tolerances should be addressed and corrected before the aircraft is flown.
learn more about system here
https://brainly.com/question/29644983
#SPJ11
a commercial refrigerator with r-134a as the working fluid is used to keep the refrigerated space at -35 c by rejecting waste heat to cooling water that enters the condenser at 18 c at a rate of 0.25 kg/s and leaves at 26 c. the refrigerant enters the condenser at 1.2 mpa and 50 c and leaves at the same pressure subcooled by 6 c. if the compressor consumes 3.3 kw of power , determine (a) the mass flow rate of the refrigerant, b) the refrigerant load, c) the cop, and d) the minimum power input to the compressor for the same refrigeration load.
Answers
At 1.2mpa pressure and 50c
What is pressure?
By pressing a knife against some fruit, one can see a straightforward illustration of pressure. The surface won't be cut if you press the flat part of the knife against the fruit. The force is dispersed over a wide area (low pressure).
a)Mass flow rate of the refrigerant
Therefore h1= condenser inlet enthalpy =278.28KJ/Kg
saturation temperature at 1.2mpa is 46.29C
Therefore the temperature of the condenser
T2 = 46.29C - 5
T2 = 41.29C
Now,
d)power consumed by compressor W = 3.3KW
Q4 = QL + w = Q4
QL = mR(h1-h2)-W
= 0.0498 x (278.26 - 110.19)-3.3
=5.074KW
Hence refrigerator load is 5.74Kg
(COP)r = 238/53
(Cop) = 4.490
Therefore the above values are the (a) mass flow rate of the refrigerant, b) the refrigerant load, c) the cop, and d) the minimum power input to the compressor for the same refrigeration load.
To learn more about pressure
https://brainly.com/question/13717268
#SPJ4
Which statement about the seal between the respirator and the wearer's face is true?
POSSIBLE ANSWERS:
Negative pressure respirators prevent ambient air from entering the mask.
Cosmetic surgery can be completed without a re-evaluation of respirator fit.
Positive pressure respirators tighten the face mask when the wearer inhales.
Facial hair can prevent a respirator from properly sealing to the wearer’s face.
Answers
A true statement about the seal between the respirator and the wearer's face is: D. facial hair can prevent a respirator from properly sealing to the wearer’s face.
What is a respirator?A respirator can be defined as a personal protective equipment that is typically worn over the face to protect the mouth and nose, while protecting the wearer from inhaling smoke, dust, or other toxic chemical substances.
In this context, a true statement about the seal between the respirator and the wearer's face is that facial hair has the ability to prevent a respirator from properly sealing to the wearer’s face.
Read more on protective equipment here: https://brainly.com/question/19131588
#SPJ1
Please choose a specific type of stability or control surface (e.g., a canard) and explain how it is used, what it is used for, and the pros and cons of the device or system.
Answers
Answer:
small forewing
pro : Can be used in place of tail plane configuration
con : Can be very complex and difficult to use
Explanation:
A canard is generally used to provide some form of stability to an unstable or semi stable system.
An example of a Canard is a small forewing placed in an aircraft that will help stabilize the aircraft when in motion( in air ). because an airplane is generally an unstable system on its own
pro : Can be used in place of tail plane configuration
con : Can be very complex and difficult to use
Q1: You have to select an idea developing an application like web/mobile or industrial, it should be based on innovative idea, not just a simple CRUD application. After selecting the idea do the following: 1) How your project will be helpful and what problem this project addresses. (10-Marks) 2) Write down the requirements. (10Marks) 3) List the functional and non-functional requirements of your project. (10marks) 4) Which process model you will follow for this project and why? (10marks) 5) Draw the Level 0, and level 1 DFD of your application. (20marks)
Answers
Answer:
Creating an app is both an expression of our self and a reflection of what we see is missing in the world. We find ourselves digging deep into who we are, what we would enjoy working on, and what needs still need to be fulfilled. Generating an app idea for the first time can be extremely daunting. Especially with an endless amount of possibilities such as building a church app.
The uncertainty has always spawned a certain fear inside creators. The fear of creating something no one will enjoy. Spending hundreds of dollars and hours building something which might not bring back any real tangible results. The fear of losing our investment to a poor concept is daunting but not random. But simple app ideas are actually pretty easy to come by.
Great app idea generation is not a gift given to a selected few, instead, it is a process by which any of us are able to carefully explore step by step methods to find our own solution to any problem. Whether you are a seasoned creator or a novice, we have provided a few recommendations to challenge and aid you as you create your next masterpiece.
if I am right then make me brainliest
i am a nice guy
right
Answers
Answer:
yes you are
Explanation:
and you will always be
Answer:
u seem pretty nice to be giving away 50 points for free lol
let 3 be the maclaurin polynomial of ()=. use the error bound to find the maximum possible value of |(1.6)−3(1.6)|. (use decimal notation. give your answer to four decimal places.)
Answers
To begin with, let's recall that the Maclaurin polynomial of a function f(x) is the Taylor polynomial centered at x = 0.
In this case, we're given that the third-degree Maclaurin polynomial of f(x) is:P3(x) = f(0) + f'(0)x + (f''(0)/2!)x^2 + (f'''(0)/3!)x^3We don't know what the function f(x) is, but we do know that its Maclaurin polynomial is P3(x), so we can use this to approximate f(x) near x = 0. Specifically, we can use P3(x) to estimate the value of f(x) at x = 1.6.However, since P3(x) is only an approximation, there will be some error involved in using it to estimate f(x). This error is given by the remainder term R3(x), which is given by:
R3(x) = f^(4)(c)x^4/4!
where c is some number between 0 and x. We don't know what c is, but we can use the fact that |f^(4)(x)| <= M for all x in an interval containing x = 1.6 to find an upper bound for R3(x). Let's assume that M = 5.Then, the error bound for our approximation of f(1.6) using P3(x) is given by:
|f(1.6) - P3(1.6)| <= |R3(1.6)| <= (5/4!)(1.6)^4
This simplifies to:
|f(1.6) - 3| <= 0.0128So the maximum possible value of |(1.6)−3(1.6)| is 0.0128. We can express this to four decimal places as 0.0128.
For such more questions on Taylor polynomial
https://brainly.com/question/2533683
#SPJ11
Give me source code of Simple openGL project. ( without 3D or Animation) simple just.
Answers
Answer:
Use GitHub or stackoverflow for this answer
Explanation:
It helps with programming a lot
Two added to four times a number, minus 3 times the number, equals 5.
Answers
x= 3.
Explanation:What is presented in this problem is basically an equation in verbal form.
1. Write the equation.
\(2+4x-3x=5\)
2. Solve for x.\(2+4x-3x=5\\ \\2+x=5\\ \\x=5-2\\ \\x=3\)
3. Express the result.x= 3.
Match the car part to the system
Catalytic Converter
Radiator
Alternator
Shock absorbers
Engine
And
Suspension system
Cooling system
Electrical system
Power train
Exhaust system
Answers
Radiator - Cooling System
Alternator - Electrical System
Shock Absorbers - Suspension System
Engine - Power train
The match up are:
Catalytic Converter - Exhaust SystemRadiator - Cooling SystemAlternator - Electrical SystemShock Absorbers - Suspension SystemEngine - Power trainWhat is an exhaust system?This is known to be a tool that is often used to aid the reaction exhaust gases as it moves away from a controlled combustion which often occurs in an engine.
Therefore, The match up are:
Catalytic Converter - Exhaust SystemRadiator - Cooling SystemAlternator - Electrical SystemShock Absorbers - Suspension SystemEngine - Power trainLearn more about Exhaust System from
https://brainly.com/question/21417514
#SPJ9
You often experiment with everyday materials around you, trying to create new and unique items. You enjoy designing and creating things that improve your daily tasks. What characteristic of a STEM student are you displaying?
A. technologically-literate
B. inventor
C. innovator
D. problem-solver
Answers
answer:D. problem-solver
The answer is:
B) Inventor