what to do if your car breaks down in the middle of nowhere
Answers
Breaking down in the middle of nowhere can be a stressful and frustrating situation.
The first step is to safely move your car off the road and turn on your hazard lights. Then, assess the situation and try to diagnose the issue. If you can't fix it, call for roadside assistance or check the internet for the nearest mechanic or towing service.
It's important to stay in your car and avoid walking long distances in unfamiliar areas. If it's hot, stay in the shade and drink water to avoid dehydration. If it's dark, use caution and stay in your car until help arrives. Always keep your phone charged and let someone know where you are and your estimated time of arrival.
Learn more about frustrating situation here:
https://brainly.com/question/14367013
#SPJ4
Related Questions
Typical journal-to-bearing clearance is......
A) 0.00015 to 0.00018 inch
B)0.0005 to 0.0025 inch
C) 0.15 to 0.25 inch
D)0.02 to 0.035 inch
Answers
C
Why
I took the quiz
The typical journal-to-bearing clearance for engines is,
B) 0.0005 to 0.0025 inch
Given that,
To find the typical journal-to-bearing clearance for engines.
Now, The range 0.0005 to 0.0025 inch represents the recommended clearance between the rotating journal of the crankshaft and the bearing surface to ensure proper lubrication and minimal friction.
Hence, The correct option for typical journal-to-bearing clearance for engines is,
B) 0.0005 to 0.0025 inch.
To learn more about journal-to-bearing visit:
https://brainly.com/question/16971319
#SPJ4
untably infinitely many; a finite number • B: uncountably infinitely many; about four billion (depending on the architecture) • C:countably infinitely many; countably infinitely many • D: countably infinitely many; uncountably infinitely many
Answers
The correct answer is A: uncountably infinitely many; a finite number.
There is a finite number, which is correct as the set of real numbers between 0 and 1 is bounded and has a finite size.
How many elements are there?The correct answer is A: uncountably infinitely many; a finite number.
This is because the set of natural numbers (1, 2, 3, ...) is countably infinite, meaning it can be put into a one-to-one correspondence with the set of positive integers. On the other hand, the set of real numbers between 0 and 1 is uncountably infinite, as it cannot be put into a one-to-one correspondence with the set of natural numbers.
The option A states that there are uncountably infinitely many elements in the set, which is true for the real numbers between 0 and 1. However, it also mentions that there is a finite number, which is correct as the set of real numbers between 0 and 1 is bounded and has a finite size.
Learn more about finite number.
brainly.com/question/1614996
#SPJ11
Liquefied Natural Gas (LNG) is a natural gas in its liquid form that is clear, colorless, odorless, non-corrosive, and non-toxic.
Answers
Answer:
liquifid gas
Explanation:
when gas is introduced to a certain chemical it ends up slowly liquifying itself.
Drag each tile to the correct box.
Arrange the steps of the basic dedsion-making process in the correct order.
identifying your choices
making a decision
identifying a need or a problem
gathering information about choices from
different sources
taking an action
analyzing your resources
evaluating your choices
Answers
Answer:
i dont know i dont think i can do it
Explanation:
Do you think that the country that has the right to force vaccinations on the community?
Answers
Answer:
no
Explanation:
we all have the freedom to choose whether we want to have something injected in our bodies that we aren't sure about. This would be a violation of our constitutional right to force us to take the vaccine.
A principle of iterative development is to implement the high-risk components of the system first. this approach best falls into what kind of development paradigm?
Answers
A principle of iterative development exists to execute the high-risk components of the system first. this approach best descends into Use-case-driven development.
What is principle of iterative development?
Iterative development exists as a software development approach that supports the development of a system incrementally. The process builds in common and frequent cycles for feedback from stakeholders established on reactions by end users to the working, although incomplete, system. Iterative software development suggests building the product step by step, which permits for the identification and correction of defects during the earlier stages, to avoid their downward flow into further processes.
One of the key elements of the Unified Process is its usage of use cases as a driving force for development. The phrase use case driven guides to the fact that the project team uses the use cases to navigate all development work, from initial gathering and negotiation of requirements through code.
To learn more about Use-case-driven refer to:
https://brainly.com/question/14493919
#SPJ4
me that both a triaxial shear test and a direct shear test were performed on a sample of dry sand. When the triaxial test is performed, the specimen was observed to fail when the major and minor principal stresses were 100 lb/in2 and 20 lb/in2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 3000 lb/ft2
Answers
Answer:
shear strength = 2682.31 Ib/ft^2
Explanation:
major principal stress = 100 Ib / in2
minor principal stress = 20 Ib/in2
Normal stress = 3000 Ib/ft2
Determine the shear strength when direct shear test is performed
To resolve this we will apply the coulomb failure criteria relationship between major and minor principal stress a
for direct shear test
use Mohr Coulomb criteria relation between normal stress and shear stress
Shear strength when normal strength is 3000 Ib/ft = 2682.31 Ib/ft^2
attached below is the detailed solution
29 10 1 point According to Gate Theory, which of the following factors can make you more sensitive to pain? Placebo effects Competing signals, like rubbing your elbow Chronic stress High levels of arousal 30 1 point Patients who are allowed to self-administer morphine use less than when they receive injections from healthcare providers. True False 31 1 point What happens when people lose their sense of smell (olfaction)? They often become manic. 32 Not much. Olfaction is not a very important sense for humans. They compensate by developing an increased sensitivity to taste (gustation). They often become depressed. 1 point The different taste qualities (sweet, sour, bitter, salt, umami) each have their own area of the tongue that is most sensitive to them. True False
Answers
The statement that The different taste qualities (sweet, sour, bitter, salt, umami) each have their own area of the tongue that is most sensitive to them is False.
Gate Theory states that competing signals such as rubbing your elbow can make you more sensitive to pain. This theory suggests that physical signals such as massage, pressure, heat, or cold can block the transmission of pain messages through the spinal cord and prevent them from reaching the brain. Therefore, when people rub their elbows or apply pressure to the area, this stimulates the non-painful touch fibers and decreases the transmission of the painful stimuli.
As per the statement, patients who are allowed to self-administer morphine use less than when they receive injections from healthcare providers is True. Olfaction is a very important sense for humans, and they often become depressed when they lose their sense of smell (olfaction). The statement that The different taste qualities (sweet, sour, bitter, salt, umami) each have their own area of the tongue that is most sensitive to them is False.
To know more about tongue please refer:
https://brainly.com/question/13178857
#SPJ11
which kind of these objects do you think is most common in our galaxy?
Answers
The kind of object that is most common in our galaxy is red dwarf stars.
Red dwarfs are the smallest and coolest type of main-sequence stars and are estimated to constitute more than 70% of the stars in the Milky Way galaxy. They have a mass range of approximately 0.08 to 0.5 solar masses and a surface temperature of less than 4,000 K, making them faint and difficult to observe.
Despite their low luminosity, red dwarfs are long-lived and can burn their fuel for trillions of years, which increases the likelihood of planets orbiting around them. It is thought that many of the known exoplanets, including potentially habitable ones, orbit red dwarf stars.
Therefore, due to their abundance and potential to host planets, red dwarfs are considered the most common type of object in our galaxy.
Learn more about Milky Way galaxy here:
brainly.com/question/31932403
#SPJ11
Were you surprised by the “pie data”? Is it true for you, your family, and your friends? Why or why not?
this is a coding question, and pie data is a misprint. It is actulaly big data.
Answers
Answer:
No because it is something to gain knowledge of peoples lives.
Answer: i was not suprised because, it is something all people need to know to gai knowledege about it.
Calculate the volume of material used in making 100 ft of 4 in. type K, copper tubing.
Answers
The volume of material used in making 100 ft of 4 in. type K, copper tubing will be 1443.3 in³ or 0.835 ft³
What is volume?Volume is a measurement of three-dimensional space that is occupied. It is frequently numerically quantified using SI-derived units or various imperial or US customary units. The definition of length is linked to the definition of volume.
Let's begin by listing out the given variables:
length (l) = 100 ft = 1200 in, nominal size = 4 in
The dimension and physical characteristics of type M copper tubing of nominal size 4 inch are given in the copper tube of industry-standard guide of the design and installation of the piping system is illustrated.
Outer diameter (Do) = 4.125 in ⇒ ro = Do ÷ 2 = 2.0625 in, Inner diameter (Di) = 3.935 in ⇒ ri = Di ÷ 2 = 1.9675 in
calculate the volume of the pipe, we use the formula
V = π(ro² - ri²) * l
V = π(2.0625² - 1.9675²) * 1200
V = 1443.3 in³ or 0.835 ft³
Learn more about volume on:
https://brainly.com/question/1972490
#SPJ1
A species A diffuses radially outwards from a sphere of radius ro. The following assumptions can be made. The mole fraction of species A at the surface of the sphere is XAO. Species A undergoes equimolar counter-diffusion with another species B. The diffusivity of A in B is denoted DAB. The total molar concentration of the system is c. The mole fraction of A at a radial distance of 10ro from the centre of the sphere is effectively zero. (a) Determine an expression for the molar flux of A at the surface of the sphere under these circumstances. Likewise determine an expression for the molar flow rate of A at the surface of the sphere. [12 marks] (b) Would one expect to see a large change in the molar flux of A if the distance at which the mole fraction had been considered to be effectively zero were located at 100ro from the centre of the sphere instead of 10ro from the centre? Explain your reasoning. [4 marks] (c) The situation described in (b) corresponds to a roughly tenfold increase in the length of the diffusion path. If one were to consider the case of 1-dimensional diffusion across a film rather than the case of radial diffusion from a sphere, how would a tenfold increase in the length of the diffusion path impact on the molar flux obtained in the 1-dimensional system? Hence comment on the differences between spherical radial diffusion and 1-dimensional diffusion in terms of the relative change in molar flux produced by a tenfold increase in the diffusion path.
Answers
(a) Molar flux of A at the surface of the sphere:Molar flux (NA) is defined as the number of moles of A that passes through a unit area per unit time. In radial flow, the molar flux of A is:NA = -DAB(∂CA/∂r) = -DAB(CA/rt)Where, rt = radius of the sphere and CA = concentration of A.Since the mole fraction of A at the surface of the sphere is XAO, then we can express the molar flow rate of A at the surface of the sphere as:NA0 = NA|rt=ro = -DAB(CAO/ro)(XAO/1 - XAO)(b) If the distance at which the mole fraction was considered to be effectively zero were located at 100ro from the centre of the sphere instead of 10ro from the centre, then there would be a large change in the molar flux of A.This is because the concentration gradient between the centre of the sphere and 100ro from the centre of the sphere would be much steeper than between the centre of the sphere and 10ro from the centre. Therefore, there would be a larger concentration gradient driving the diffusion of A, which would result in a larger molar flux of A.(c) If one considers the case of 1-dimensional diffusion across a film rather than the case of radial diffusion from a sphere, then a tenfold increase in the length of the diffusion path would result in a roughly tenfold decrease in the molar flux obtained in the 1-dimensional system. This is because the molar flux is directly proportional to the concentration gradient, and a tenfold increase in the length of the diffusion path would result in a tenfold decrease in the concentration gradient.In terms of the relative change in molar flux produced by a tenfold increase in the diffusion path, there is a greater relative change in molar flux produced by a tenfold increase in the diffusion path in the case of 1-dimensional diffusion across a film than in the case of radial diffusion from a sphere. This is because the concentration gradient is much steeper in the case of radial diffusion from a sphere, which means that the molar flux is less affected by a change in the length of the diffusion path.
Identify the true statement for the given 3-bit shift-right and load register if D is 011, shr_in is 1, shr is 1, Id is 0, and Q is 010. Consider a rising clock edge.
Q I. The present value is shifted; therefore, Q becomes 101
O II. The present value is shifted; therefore, Q becomes 111
O III. The present value of D is loaded into Q; thus, Q becomes 011
O IV. The present value of Q is maintained; therefore, Q remains 010
Answers
The true statement for the given 3-bit shift-right and load register if D is 011, shr_in is 1, shr is 1, Id is 0, and Q is 010, considering a rising clock edge is option IV) The present value of Q is maintained; therefore, Q remains 010.
Based on the given conditions:
D = 011
shr_in = 1
shr = 1
Id = 0
Q = 010
Considering a 3-bit shift-right operation with a rising clock edge, let's evaluate each statement:
I. The present value is shifted; therefore, Q becomes 101.
In a shift-right operation, the bits in the register are shifted to the right. The rightmost bit (shr_in) is shifted into the leftmost position. Since Q initially contains 010, after the shift-right operation, Q would become 001 (with shr_in as the leftmost bit), not 101 as mentioned in Option I. Therefore, Option I is not the correct statement.
II. The present value is shifted; therefore, Q becomes 111.
Similar to Option I, this statement suggests that the present value of Q will be shifted, resulting in Q becoming 111. However, based on the given conditions, the initial value of Q is 010, and a 3-bit shift-right operation will not change the value of Q. Therefore, Option II is also not the correct statement.
III. The present value of D is loaded into Q; thus, Q becomes 011.
This statement suggests that the value of D (011) is loaded into Q, which would mean Q is updated to 011. However, the given conditions do not mention any load operation, only a shift-right operation. Therefore, Option III is not the correct statement.
IV. The present value of Q is maintained; therefore, Q remains 010.
This statement is the correct one. Since the given conditions specify a 3-bit shift-right operation with no load, the present value of Q will be maintained. Hence, Q remains 010 after the shift-right operation.
Therefore, the correct statement is:
IV. The present value of Q is maintained; therefore, Q remains 010.
Learn more about shift register at:
brainly.com/question/14096550
#SPJ11
What failure(s) would you suspect if the output of a 3-input NAND gate stays HIGH no matter what the inputs are
Answers
Answer:A 4-input NAND gate is normally high. It can only go low when all four of the inputs have a logical high on them. Assuming the circuit should see a condition where all four inputs go high, then a constant high output indicates a fault does exist.The first step in troubleshooting this failure is to verify the circuit, under normal operation should be seeing a condition where all four inputs do go high. It is completely possible that the circuit is working properly and the condition you were expecting simply does not occur. Verifying what your inputs should be allow you to confirm whether a failure exists in reality.Second, you should verify that the logic probe, multi-meter, oscilloscope, logic analyzer, or monitoring circuit you are using to test circuit outputs is working properly. This is easiest done by touching the probe of the monitoring device to another output you should see changing states. In one system I once had to trouble-shoot, the device had a built-in monitoring circuit and the failure was actually in the monitoring circuit rather than in the main circuit. Once you have confirmed that your test equipment is working properly, you can begin testing the actual circuit to troubleshoot the failure.Given that the circuit should be seeing periods where the gate should go low and that your test equipment is working properly, then a constant high output on this gate means either the output of the gate is open (assuming their is a tie-up resistor somewhere on the output line) or at least one of the inputs is being held low. A constant low input could be a failed gate driving one of the inputs, a short to ground on the circuit board trace connected to the constant low input, or a tie-up resistor on the input that has opened (Technically, this last cause creates a floating input which could intermittently be seen as either a high or low, but in my experience is invariably seen as a low.) The only way to determine which fault exists is to measure the voltages on each input pin to determine which input is failing and then trace the constant low back to its source.729 viewsView 1 upvote1Add a comment...Sponsored by Purdue University OnlinePurdue's 100% Online Master's Now Accepting Applications.Earn an online MS in Electrical and Computer Engineering degree in 12-24 months. View curriculum guide.Learn MoreLoring Chien, Electrical Engineer for 45 years & IEEE Sr. Life memberAnswered Jul 2, 2020
Explanation:
the water depths upstream and downstream of a hydraulic jump is 0.3 m and 1.2 m. Determine flow rate
Answers
This question is incomplete, the complete question is;
the water depths upstream and downstream of a hydraulic jump is 0.3 m and 1.2 m. Determine flow rate ( in m³ ) if the rectangular channel is 20 m wide.
Answer:
the flow rate is 32.549 m³/sec
Explanation:
Given that
y₁ = 0.3 m
y₂ = 1.2 m
β = 20 m
Now for Rectangular Channel, we know that;
2q²/g = y₁y₂( y₁ + y₂)
where g = 9.81 m/s²
and q = Q/β
so
2(Q/β)²/g = y₁y₂( y₁ + y₂)
we substitute our given values
2(Q/20)²/9.81 = 0.3 × 1.2( 0.3 + 1.2)
2(Q²/400)/9.81 = 0.36(1.5)
2(Q²/400) = 0.54 × 9.81
Q²/400 = 5.2974 / 2
Q²/400 = 2.6587
Q² = 1059.48
Q = √1059.48
Q = 32.549 m³/sec
Therefore the flow rate is 32.549 m³/sec
the benchmark is 100.00. the backsights are 4.00, 6.32 and 12.75. the foresights are 6.00, 9.00 and 3.22. what is the elevation of the point?
Answers
The elevation of the point is 104.85.
To find the elevation of the point, we need to use the following formula:
Elevation of point = Benchmark + Backsight - Foresight
Here,
BM = Benchmark = 100.00
To determine the elevation of the point with the given benchmark, backsights, and foresights, follow these steps:
1. Calculate the sum of the backsights: 4.00 + 6.32 + 12.75 = 23.07
2. Calculate the sum of the foresights: 6.00 + 9.00 + 3.22 = 18.22
3. Subtract the sum of the foresights from the sum of the backsights: 23.07 - 18.22 = 4.85
4. Add the result to the benchmark: 100.00 + 4.85 = 104.85
Therefore, the elevation of the point is 104.85.
Learn more about benchmark: https://brainly.com/question/14666679
#SPJ11
What are shims used for ?
Answers
Objective A: Right turn True or Flase
Answers
Answer:
True
Explanation:
Because a object is a smart thing to use doing them problem
What materials were used in the construction of Colorado Capitol HIll?
Answers
Answer Designed by Elijah E. Myers, it was constructed in the 1890s from Colorado white granite, and opened for use in November 1894. The distinctive gold dome consists of real gold leaf, first added in 1908, commemorating the Colorado Gold Rush.
Location: 200 East Colfax Avenue; Denver, Co...
Part of: Denver Civic Center (ID12001017)
Built: 1886–1901
Added to NRHP: October 16, 2012
Explanation:
Prove the dimension of dynamic viscosity in MLTt system
(ML^-1T^-1).
Write the equations of the forces and their dimensions which are
important in fluid mechanics
Answers
The dimension of dynamic viscosity in the MLTt system is ML^-1T^-1, derived from the ratio of shear stress to the rate of shear strain in a fluid.
Shear stress (τ) is defined as the force (F) per unit area (A) required to maintain a velocity gradient in the fluid. Its dimensions can be written as [F]/[A] = [M][L]^-1[T]^-2.Velocity gradient (du/dy) represents the change in velocity (du) with respect to the change in distance (dy) perpendicular to the flow. Its dimensions can be written as [du]/[dy] = [L][T]^-1.Therefore, the dimension of dynamic viscosity (μ) can be obtained by dividing the dimensions of shear stress by the dimensions of velocity gradient:[μ] = [τ] / [du/dy] = [M][L]^-1[T]^-2 / ([L][T]^-1) = [M][L]^-1[T]^-1.Hence, the dimension of dynamic viscosity in the MLTt system is [M][L]^-1[T]^-1, which represents mass per unit length per unit time.
To know more about dynamic click the link below:
brainly.com/question/30464801
#SPJ11
When in regular operation, ash and other debris should be removed _______ from the combustion chamber of a wood-burning heater.
Answers
When in regular operation, ash and other debris should be removed daily from the combustion chamber of a wood-burning heater.
What is meant by a combustion chamber?A wood stove radiates heat as it warms up via the stove's top and walls. The nearby region is warmed by the radiant heat, which can also warm other areas of the house thanks to the natural airflow in the building.
Fans using electric or convection power can help move this heat around to warm a bigger space. Some wood stoves use a convection chamber that wraps around the firebox to combine radiant and convection heat into a single appliance. Cool air is drawn into this convection chamber where it is heated and then circulated once again around the space.
Ash and other debris should be taken out of a wood-burning heater's combustion chamber every day when it is in regular use.
To learn more about combustion chamber refer to;
https://brainly.com/question/7324023
#SPJ4
Disposable income equals: Multiple choice question. personal income minus personal taxes. national income minus transfer payments. personal income minus transfer payments. national income minus taxes plus government spending.
Answers
The correct answer is Disposable income equals: personal income minus personal taxes.
How is disposable income calculated?Disposable income refers to the amount of money an individual or household has available for spending or saving after deducting personal taxes from their total personal income.
It represents the actual income that individuals can use to meet their consumption needs or invest in various financial assets.
Personal income refers to the total amount of income earned by individuals from various sources, including wages, salaries, dividends, and rental income.
Personal taxes, on the other hand, represent the portion of personal income that individuals are required to pay to the government in the form of income taxes.
By subtracting personal taxes from personal income, disposable income provides a more accurate measure of the funds individuals have at their disposal.
It reflects their actual purchasing power and economic well-being, allowing them to make decisions regarding consumption, savings, and investments.
Disposable income is an important indicator in analyzing individual and household spending patterns and understanding the overall economic conditions affecting consumers. Therefore, correct answer is Disposable income equals personal income minus personal taxes.
Learn more about Disposable income
brainly.com/question/1810376
#SPJ11
What is the outer part of a ship called?
Answers
The outer part of a ship is called deck. the tallest deck along the length of the vessel, from stem to stern.
Vehicle deck: (naval) a deck or decks used to transport vehicles on amphibious assault ships; a deck used for a similar purpose aboard passenger ferries and other commercial vessels. Any deck that is outside is a weather deck. The watertight body of a ship, boat, or flying boat is known as the hull. The hull may be completely or partially covered by a deck, or it may open at the top (like a dinghy). A deckhouse and other superstructures, such as a funnel, derrick, or system, may be located on top of the deck.
Learn more about system here-
https://brainly.com/question/27162243
#SPJ4
What will occur when the trough of Wave A overlaps the trough of Wave B?
Destructive interference will occur, causing the new wave to have more energy than Wave A or Wave B.
Constructive interference will occur, causing the new wave to have more energy than Wave A or Wave B.
Destructive interference will occur, causing the new wave to have less energy than Wave A or Wave B.
Constructive interference will occur, causing the new wave to have less energy than Wave A or Wave B.
Answers
Answer:
B- Constructive interference will occur, causing the new wave to have more energy than Wave A or Wave B.
Explanation:
What will occur when the trough of Wave A overlaps the trough of Wave B is; B: Constructive interference will occur, causing the new wave to have more energy than Wave A or Wave B.
What is constructive interference of waves?Wave interference is simply defined as the phenomenon that transpires when two waves meet each other while traveling along the same medium.
Now, this meeting of the waves in interference could either be constructive interference or destructive interference.
Constructive interference is the type that occurs where the waves cross over each other in such a way that the two waves are in phase while Destructive interference is a wave interference that occurs where two waves are completely out of phase.
Looking at the question it says they overlap each other and this denotes constructive interference and a new wave will be formed with more energy than the parent waves.
Read more about Constructive Interference of Waves at; https://brainly.com/question/1346741
As You Read Connect How can identifying your interests help you to succeed at school and at work?
Answers
Answer:
Explanation:
Identifying your interests can help you to succeed at school and at work in a few key ways. First, having an understanding of what interests you can help you to focus on the subjects that you are most passionate about, which can lead to higher grades and better performance. Additionally, having an understanding of your interests can help you to choose a major, a job, or a career that will be most rewarding and beneficial to you. Knowing what interests you can also help you to develop goals and objectives that will give you a sense of direction and focus. Finally, being aware of your interests can help you to find an organization or group that shares your values and interests, which can provide greater job satisfaction and lead to more success.
Producing airplanes is complex that the necessary expertise and resources to manufacture different components are spread across the world, for instance, Boeing has more than 15,000 suppliers in 81 countries.
Select one:
a. International suppliers
b. Fully integrated global supply chain
c. Off shore manufacturing
d. International distribution system
Answers
Answer:
D. International distribution system
brenda cassini (bcassini) was recently married. you need to update her linux user account to reflect her new last name of palmer. you are currently logged in as the root account, so you won't need to use the sudo command to get permissions to perform the required tasks.
Answers
The task is to update her last name from "Cassini" to "Palmer" in the Linux user account.
What is the task that needs to be performed on Brenda Cassini's Linux user account?The task at hand is to update the Linux user account of Brenda Cassini (username: bcassini) to reflect her new last name of Palmer.
Since the user account needs to be updated, it requires administrative privileges, which in this case, are already available as the user is logged in as the root account.
The necessary steps to perform the task would include accessing the user account settings, editing the user account name, and saving the changes. Once the changes are made and saved, the user account will be updated to reflect the new last name of Palmer.
It is important to note that updating user account information should be done with caution and the appropriate permissions.
Learn more about task
brainly.com/question/16930671
#SPJ11
A thin plate 0.7 m long and 1.5 m wide is submerged and held stationary in a stream of water
Answers
The thickness of the boundary layer will be 0.436m. Distance downstream of the leading edge where this Reynolds number occur will be 3.08mm. The shear stress on the plate on this point is 1.055 N/m².
Why is the Reynolds number employed?Laminar or turbulent fluid flow is identified using the Reynolds number, abbreviated as Re. In all viscous flows, where a numerical model is chosen in accordance with pre-calculated Reynolds number, it is one of the primary regulating parameters.
How to solve the question?Given, Reynolds number, Re = 500000
length = 0.7 m
width = 1.5m
velocity, u = 1.5 m/s
the thickness of the boundary layer, Re = u×x/v
x = Re × v/u
x = 500000×1.31×10∧(-6)/1.5
x = 0.436m
distance downstream of the leading edge where this Reynolds number occur, δ = 5x/\(\sqrt{Re}\)
δ = 5×0.436/√500000
δ = 3.08 mm
The shear stress on the plate on this point,
τ = 0.332v(u/x)×√Re
τ = 0.332×1.31×10∧(-3) (1.5/0.436) √500000
τ = 1.055 N/m²
To know more about Reynold's number visit
brainly.com/question/12977616
#SPJ4
The complete question is,
A thin plate 0.7 m long and 1.5 m wide is submerged and held stationary in a stream of water (T = 10°C) that has a velocity of 1.5 m/s. What is the thickness of the boundary layer on the plate for Re, 500,000 (assume the boundary layer is still laminar), and at what distance downstream of the leading edge does this Reynolds number occur? What is the shear stress on the plate on this point?
Write a program to play the Card Guessing Game. Your program must give the user the following choices: - Guess only the face value of the card. - Guess only the suit of the card. - Guess both the face value and the suit of the card. Before the start of the game, create a deck of cards. Before each guess, use the function random_shuffle to randomly shuffle the deck.
Answers
how am I going to do this, I have a friend that might be able to help I will check
Task 3: the instantride finance team wants to collect the price and discount information with the driver names for each travel in the system. You need to return the travel id, driver first name, driver last name, travel price, and travel discount information from the travels and drivers tables combined over driver id field with the on keyword.
task
calculate each user's price and discount information
Answers
By using this information to calculate each user's price and discount information, they can make informed decisions about how to optimize pricing and discounts to drive customer loyalty and increase revenue.
To collect the price and discount information with the driver names for each travel in the system, we need to query the travels and drivers tables combined over the driver ID field. The query should return the travel ID, driver first name, driver last name, travel price, and travel discount information.
Once we have this information, we can calculate each user's price and discount information. We can do this by grouping the data by driver ID and then calculating the total price and discount for each driver. This will give us an overview of how much each driver has earned and how much they have discounted for their customers.
In order to ensure that the content loaded into the system is accurate, it is important to regularly check the data and update it as needed. This will help to ensure that the finance team has access to the most up-to-date information and can make informed decisions about pricing and discounts.
Overall, collecting and analyzing data on travel prices and discounts is crucial for the success of the InstantRide finance team. By using this information to calculate each user's price and discount information, they can make informed decisions about how to optimize pricing and discounts to drive customer loyalty and increase revenue.
For more such questions on discount information:
https://brainly.com/question/15202870
#SPJ11